NACE NACE-CIP1-001 Practice Exam - 100 Unique Questions
Latest Questions NACE-CIP1-001 Guide to Prepare Free Practice Tests
NACE-CIP1-001 certification exam is recognized worldwide and is often required by government agencies and private companies for coating inspection jobs. In addition to the Level 1 certification, NACE offers higher level certifications for coating inspectors, including Level 2 and Level 3. These certifications require more experience and knowledge, and demonstrate advanced skills in the field.
NEW QUESTION # 55
Common errors that may produce inaccurate readings when using a Dial-Type Magnetic Pull-Off Dry Filth Thickness (DFT) gauge include:
Select All That Apply
- A. Rotating the dial too fast when taking measurements
- B. Taking measurements too far from the edge of a surface
- C. Measuring ditty, tacky, or soft films
- D. Failing to determine the base metal reading (BMR)
Answer: A,C,D
NEW QUESTION # 56
When using the ISO comparator in accordance with ISO 8503, if the surface profile does not directly compare to one of the four segments the inspector should:
- A. Use another method as the comparator method is too subjective
- B. Record your result by identifying two segments
- C. Record the segment with the more aggressive profile
- D. Record the segment with the less aggressive profile
Answer: D
NEW QUESTION # 57
If a Thermoset coating is heated it will:
- A. Harden and return to its original hardness when cooled
- B. Harden and retain its hardness when cooled
- C. Soften when heated and return to its original hardness when cooled
- D. Soften when heated and retain its softness when cooled
Answer: B
NEW QUESTION # 58
What is used to determine compressed air cleanliness?
- A. Profilometer
- B. Needle pressure gauge
- C. Blotter test
- D. Psychrometer
Answer: A
NEW QUESTION # 59
You ate the NACE Inspector on a job where NACE No. 2/SSPC - SP 10 has been specified. You are finding the Contractor is leaving mill scale on the on surface and as a result you have been rejecting the blast. The Contractor is very upset and has told you that the standard permits up to 5% of the mill scale to remain and still be in be in compliance with the standard.
Your FIRST preferred course of action is to:
- A. Call your supervisor
- B. Shut the job down
- C. Permit coating to take place so as not to lose the blast
- D. Review the relevant standard with the Contractor
Answer: D
NEW QUESTION # 60
You are the NACE Inspector on a job where the Owner's specification requites you to perform a twice daily check of blast pressure at the nozzle. It is now day 30 on the job and all of your readings have been within compliance. The Contractor complains that these checks taking up much time and in view of the compliant results they are unnecessary.
Your FIRST preferred course of action is to:
- A. Skip the checks as you are. confident the blast pressure is OK
- B. Skip the checks and just record the same readings as you have been getting
- C. Keep doing the checks regardless
- D. Keep doing the checks and consult the Owner's representative for direction
Answer: D
NEW QUESTION # 61
You are the NACE Inspector on a tank lining project where a 50% solids epoxy tank lining is being applied. After application of the 19 coat you notice small blisters in some areas of the applied lining.
Your FIRST preferred course of action is to:
- A. Document the problem and advise the Contractor and Owner's representative
- B. Document the problem and advise the Contractor
- C. Extract any liquid that may be inside the blister and send it to the lab for further analysis
- D. Break the blisters to see what's inside
Answer: A
NEW QUESTION # 62
What is the minimum spot measurement value allowed by SSPC-PA 2 in each 10 m2 (100 ft2) area?
- A. 90% of the specified maximum thickness
- B. 70% of the specified maximum thickness
- C. 100% of the specified maximum thickness
- D. 80% of the specified minimum thickness
Answer: D
NEW QUESTION # 63
Which one of the following documents is the best source for coating technical data:
- A. Technical Data Sheet
- B. Safety Data Sheet;
- C. Application Guidelines
- D. Specification
Answer: A
NEW QUESTION # 64
The initial steel condition is important to the NACE Inspector because:
- A. The Inspector may have to reject the Steel
- B. Less abrasive is need if the mill Scale s gone
- C. It affects the final appearance after blasting
- D. If the steel is pitted more coating will be required
Answer: A
NEW QUESTION # 65
Daily reports are important because:
Select All That Apply
- A. The information aids communication with supervisors.
- B. Management uses them to make personnel decisions.
- C. the information impacts future projects.
- D. Inspectors rarely change on a project.
Answer: A,B,C
NEW QUESTION # 66
A NACE Coating Inspector is permitted to transport coating material when:
- A. Asked to do so by the Coating Application team
- B. Asked to do so by the Owner's Representative
- C. If the Inspector meets all the necessary requirements for Transportation of Dangerous Goods
- D. The Inspector should never transport coating material
Answer: D
NEW QUESTION # 67
Check abrasive blast pressure with a
- A. needle pressure gauge
- B. surface comparator
- C. replica tape
- D. nozzle aperature gauge
Answer: A
NEW QUESTION # 68
An Inspector should change position when:
- A. Only when directed by the supervisor
- B. The Inspector is convinced by verifiable facts
- C. The Owner can save some money by the change
- D. The Inspectors position is not the majority position
Answer: B
NEW QUESTION # 69
Solvents are added to coating formulations to
- A. dissolve binders and form liquid coatings.
- B. provide color.
- C. decrease film permeability.
- D. increase film permeability.
Answer: A
NEW QUESTION # 70
If the specifier does not identify a restriction level in accordance with SSPC PA 2, the default restriction level is:
- A. Level 4
- B. Level 1
- C. Level 3
- D. Level 2
Answer: C
NEW QUESTION # 71
Dew point is the temperature at which
- A. humidity decreases
- B. condensation occurs.
- C. the air is saturated.
- D. water freezes.
Answer: B
NEW QUESTION # 72
Inspection documentation is important because:
- A. Owners use the documentation for a variety of purposes
- B. a) only
- C. It is the only deliverable item provided by the inspector
- D. a) & b)
Answer: A
NEW QUESTION # 73
......
The NACE NACE-CIP1-001 exam covers a wide range of topics related to coating inspection, including surface preparation, coating application, inspection methods, and safety procedures. NACE-CIP1-001 exam consists of two parts – a written test and a practical exam. The written test consists of 120 multiple-choice questions that are designed to evaluate the candidate's knowledge of coating inspection techniques and principles. The practical exam requires candidates to demonstrate their ability to inspect coating systems in a real-world setting.
Correct and Up-to-date NACE NACE-CIP1-001 BrainDumps: https://getfreedumps.passreview.com/NACE-CIP1-001-exam-questions.html