Free D-PDC-DY-23 pdf Files With Updated and Accurate Dumps Training
Top-Class D-PDC-DY-23 Question Answers Study Guide
NEW QUESTION # 94
Match the type of OSPF packets with its description. There are more packet descriptions than OSPF packets.
- A. OSPF Packet type 1 - a) Link State Request
OSPF Packet type 2 - f) Link Local Address
OSPF Packet type 3 - b) Hello
OSPF Packet type 4 - d) Link State Acknowledgement
OSPF Packet type 5 - c) Database Description - B. OSPF Packet type 1 - a) Link State Request
OSPF Packet type 2 - f) Link Local Address
OSPF Packet type 3 - c) Database Description
OSPF Packet type 4 - d) Link State Acknowledgement
OSPF Packet type 5 - e) Link State Update - C. OSPF Packet type 1 - a) Link State Request
OSPF Packet type 2 - f) Link Local Address
OSPF Packet type 3 - e) Link State Update
OSPF Packet type 4 - d) Link State Acknowledgement
OSPF Packet type 5 - c) Database Description - D. OSPF Packet type 1 - a) Link State Request
OSPF Packet type 2 - b) Hello
OSPF Packet type 3 - c) Database Description
OSPF Packet type 4 - d) Link State Acknowledgement
OSPF Packet type 5 - e) Link State Update
Answer: D
NEW QUESTION # 95
Refer to the exhibit:
From S1, a ping to the host address of 192.168.37.3 is not successful. The routing table on S1 shows three directly connected networks (including the Lo0 network of S1). Network 192.168.34.0/24 and the Lo0 networks of S2 and S3 are the only OSPF-learned networks in the routing table. The system on the
192.168.37.0/24 network can ping S3.
Which command offers a solution to the inability to ping the host address from S1?
- A. S3(config-router-ospf-1)# redistribute connected
- B. S3(config-router-ospf-1)# update-source loopback 0
- C. S1(config-router-ospf-1)# ip route 192.168.37.0/24 interface null 0
- D. S1(config-router-ospf-1)# network 192.168.37.0/24
Answer: A
NEW QUESTION # 96
Multicast flood restrict is a feature enabled by default on OS10 switches to ensure that no traffic drop occurs.
What is a recommended configuration step for its implementation?
- A. Configure the interface between the PIM routers as a dynamic multicast router port
- B. Disable IGMP snooping on the VLAN between two PIM routers with no IGMP receivers on that VLAN
- C. Enable IGMP snooping on the VLAN interfaces between two PIM routers with no IGMP receivers
- D. Configure the interface between the PIM routers and the rendezvous point as a static multicast router port
Answer: B
NEW QUESTION # 97
Two Dell Networking OS10 switches in a VLT configuration must be upgraded.
How will the reload of these switches proceed to result in the default initial state?
- A. Reload the primary VLT node and wait for it to join as secondary.
Wait until after delay restore timer has expired.
Reload VLT secondary node and wait for it to join as secondary. - B. Reload the primary VLT node.
This will automatically trigger the simultaneous reload of the secondary node. - C. Reload the primary VLT node.
This process will automatically trigger the reload of the secondary node after it has recovered. - D. Reload the primary VLT node and wait for it to join as primary.
Wait until after delay restore timer has expired.
Reload VLT secondary node and wait for it to join as secondary.
Answer: A
NEW QUESTION # 98
What is a characteristic of a static LAG on a Dell Networking OS10 switch?
- A. Uses LACP for management only
- B. Does not use any protocol for configuration and management
- C. Does not allow reconfiguration of the predefined ports
- D. Uses LACP for configuration only
Answer: B
NEW QUESTION # 99
In a Layer 3 Leaf-Spine topology what can be used to move Layer 2 traffic between racks?
- A. Trunks
- B. Port channel
- C. VXLAN
- D. VLT
Answer: C
NEW QUESTION # 100
Which two options describe the differences between Layer 2 and Layer 3 QoS? (Select 2)
- A. DSCP implements seven unique traffic classes for packet queueing.
- B. CoS priorities are encoded in the IP header.
- C. DSCP priorities are a combination of Class Selector and Drop Precedence.
- D. 802.1P trust-maps only trigger against 802.1Q tagged traffic.
Answer: A,C
NEW QUESTION # 101
Which two steps are required when configuring ports to operate in a VLT port channel? (Select 2)
- A. Configure the channel-group member under the physical interface.
- B. Configure the physical interface as a VLT port channel.
- C. Configure the port channel interface as a VLT port channel.
- D. Configure the channel-group member under the port channel interface.
Answer: A,C
NEW QUESTION # 102
Refer to the exhibit.
A network administrator is attempting to configure a static route on OS10-A to reach the loopback0 address on OS10-B.
Why is the ping failing?
- A. Interface Eth1/1/2 is a member of the wrong VRF on OS10-A
- B. The route has been added to the incorrect VRF on OS10-A
- C. The route is pointing to the wrong next-hop on OS10-A
- D. OS10-B must share a common VRF
Answer: B
NEW QUESTION # 103
What is an attribute of OS10 Enterprise Edition?
- A. Includes full programmability
- B. No license needed
- C. Free download
- D. Provides a GUI
Answer: A
NEW QUESTION # 104
A network administrator is troubleshooting VLT behavior where all VLT port channels are down on both VLT peers.
What type of mismatch can cause this issue?
- A. System MAC mismatch
- B. VLT LAG ID mismatch
- C. Spanning-tree mismatch at port level
- D. Spanning-tree mismatch at global level
Answer: D
NEW QUESTION # 105
The network administrator wants to configure RADIUS authentication for VTY access, and for console access to use the local configuration.
Which two commands should be used to achieve this goal?
- A. aaa authentication login vty radiusaaa authentication login console group local
- B. aaa authentication login default group radius aaa authentication login console local
- C. aaa authentication login default group radius aaa authentication login console group local
- D. aaa authentication login vty group radius aaa authentication login console local
Answer: B
NEW QUESTION # 106
How are multiple hardware based ACLs filtered?
- A. NPU
- B. DHCP
- C. IP
- D. NTP
Answer: A
NEW QUESTION # 107
Refer to the exhibit:
A network administrator is validating a VLT domain configuration using the show vlt all command.
Which user configurable VLT setting shows a default value?
- A. Role priority
- B. Peer-routing status
- C. Delay-restore timer
- D. VLT MAC address
Answer: C
NEW QUESTION # 108
On what does PBR base routing decisions?
- A. Administrator-defined forwarding
- B. Shortest path
- C. Batch traffic
- D. Dijkstra Algorithm
Answer: A
NEW QUESTION # 109
A network administrator wants servers to avoid spanning-tree convergence immediately after connecting to a leaf switch.
Which spanning-tree feature would allow this?
- A. spanning-tree port-type edge
- B. spanning-tree port-priority 0
- C. spanning-tree vlan priority 0
- D. spanning-tree port-type disabled
Answer: A
NEW QUESTION # 110
Which Ethernet interface speeds do Dell Networking OS10 switches support?
- A. 10, 16, and 40Gb
- B. 1, 2, and 100Gb
- C. 1, 10, and 25Gb
- D. 4, 8, and 32Gb
Answer: C
NEW QUESTION # 111
Considering OSPF router types, which statement is true about an ASBR?
- A. Gateways to other network domains using other routing protocols.
- B. Gateways to other network areas using the same routing protocol.
- C. Gateways to other network areas using other routing protocols.
- D. Gateways to other network domains using the same routing protocol.
Answer: A
NEW QUESTION # 112
An administrator wants certain traffic in a queue to always get bandwidth.
Which scheduler type should be used?
- A. WDRR
- B. Priority
- C. Strict
- D. WRED
Answer: C
NEW QUESTION # 113
......
Real Updated D-PDC-DY-23 Questions & Answers Pass Your Exam Easily: https://getfreedumps.passreview.com/D-PDC-DY-23-exam-questions.html